Answer
Verified
383.7k+ views
Hint:In order to answer this question,we are going to apply the concept of stress and strain and discuss about the relationship between them.We have to check the stress-strain graph according to which proportional limit is followed by elastic limit and yield point.
Complete step by step answer:
For this we have to consider the stress strain curve of a general material.
-A stress-strain curve of a material gives the relationship between stress and strain which is obtained by applying load to the material gradually. This curve reveals many of the properties of a material, for example, the Young's modulus, etc.
-The first region is the linear elastic region. In this region, the stress and strain are proportional, that is, obeys the general Hooke's law, and the slope is Young's modulus. In this region, the material only deforms plastically before it reaches the elastic limit. The end of the stage is the starting point of plastic deformation. The stress component of this point is defined as yield strength (or the yield point).
-The second stage is the strain hardening region. This region starts because the stress goes on the far side the yielding purpose, reaching a most at the last word strength point, that is the greatest stress which will be sustained and is termed the ultimate tensile strength.
-The third region is the necking region. On the far side tensile strength, a neck forms wherever the native cross-sectional space becomes considerably smaller than the average.
The necking deformation is non-uniform and can reinforce itself because the stress concentrates additional at little sections. Such feedback results in fast development of necking and leads to failure or fracture.
So, as we can see from the graph the correct answer is option (A).
Note:We have to keep in mind that the stress strain curve can be a little different for a specific material but the general curve gives the basic properties of all materials. So, until it is mentioned in the question that we have to consider a specific material, we would follow the general stress strain curve.
Complete step by step answer:
For this we have to consider the stress strain curve of a general material.
-A stress-strain curve of a material gives the relationship between stress and strain which is obtained by applying load to the material gradually. This curve reveals many of the properties of a material, for example, the Young's modulus, etc.
-The first region is the linear elastic region. In this region, the stress and strain are proportional, that is, obeys the general Hooke's law, and the slope is Young's modulus. In this region, the material only deforms plastically before it reaches the elastic limit. The end of the stage is the starting point of plastic deformation. The stress component of this point is defined as yield strength (or the yield point).
-The second stage is the strain hardening region. This region starts because the stress goes on the far side the yielding purpose, reaching a most at the last word strength point, that is the greatest stress which will be sustained and is termed the ultimate tensile strength.
-The third region is the necking region. On the far side tensile strength, a neck forms wherever the native cross-sectional space becomes considerably smaller than the average.
The necking deformation is non-uniform and can reinforce itself because the stress concentrates additional at little sections. Such feedback results in fast development of necking and leads to failure or fracture.
So, as we can see from the graph the correct answer is option (A).
Note:We have to keep in mind that the stress strain curve can be a little different for a specific material but the general curve gives the basic properties of all materials. So, until it is mentioned in the question that we have to consider a specific material, we would follow the general stress strain curve.
Recently Updated Pages
Basicity of sulphurous acid and sulphuric acid are
Assertion The resistivity of a semiconductor increases class 13 physics CBSE
Three beakers labelled as A B and C each containing 25 mL of water were taken A small amount of NaOH anhydrous CuSO4 and NaCl were added to the beakers A B and C respectively It was observed that there was an increase in the temperature of the solutions contained in beakers A and B whereas in case of beaker C the temperature of the solution falls Which one of the following statements isarecorrect i In beakers A and B exothermic process has occurred ii In beakers A and B endothermic process has occurred iii In beaker C exothermic process has occurred iv In beaker C endothermic process has occurred
The branch of science which deals with nature and natural class 10 physics CBSE
What is the stopping potential when the metal with class 12 physics JEE_Main
The momentum of a photon is 2 times 10 16gm cmsec Its class 12 physics JEE_Main
Trending doubts
Fill the blanks with the suitable prepositions 1 The class 9 english CBSE
Difference between Prokaryotic cell and Eukaryotic class 11 biology CBSE
Difference Between Plant Cell and Animal Cell
Fill the blanks with proper collective nouns 1 A of class 10 english CBSE
What is the color of ferrous sulphate crystals? How does this color change after heating? Name the products formed on strongly heating ferrous sulphate crystals. What type of chemical reaction occurs in this type of change.
One Metric ton is equal to kg A 10000 B 1000 C 100 class 11 physics CBSE
Change the following sentences into negative and interrogative class 10 english CBSE
Net gain of ATP in glycolysis a 6 b 2 c 4 d 8 class 11 biology CBSE
What organs are located on the left side of your body class 11 biology CBSE