I need correct answer in 20 minutes please Find the cycle efficiency and specific steam consumption of a reheat cycle (Fig. 2.7a) operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450 °C. Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected Boiler Reheater a High-P turbine. P= Ps= Preheal Pump Low-P turbine Condenser High-pressure turbine Reheating Low-pressure turbine

I need correct answer in 20 minutes please Find the cycle efficiency and specific steam consumption of a reheat cycle (Fig. 2.7a) operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450 °C. Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected Boiler Reheater a High-P turbine. P= Ps= Preheal Pump Low-P turbine Condenser High-pressure turbine Reheating Low-pressure turbine

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider below ideal reheat Rankine Cycle (operating with water):a) Draw T-s diagramb) Mass flow ratec) Thermal efficiencyd) Thermal power supplied to the burnere) Carnot efficiencyf) Second law efficiency of this cycle xx=40 , yy=20
1. In a steam power cycle, steam enters the turbine at 30bar with the following different conditions and leaves at 1bar. Calculate Carnot efficiency, Rankine efficiency, condenser heat flow in kW assuming mass flow rate of steam as 9.5kg/s and steam rate for each case considering the pump work. Using mollier diagram (ii)Wet with 0.95 dryness
PLEASE ANSWER LETTER D AND E WITH COMPLETE SOLUTION, THANK U 1. Steam is the working fluid in an ideal Rankine cycle. The saturated vapor enters the turbine at 8.0 MPa and saturated liquid exits the condenser at a pressure of 0.008 MPa. The net power output of the cycle is 100 MW. Determine for the cycle (a) the thermal efficiency, (b) the mass flow rate of the steam, in kg/h, (c) the rate of heat transfer, into the working fluid as it passes through the boiler, in MW, (d) the rate of heat transfer, from the condensing steam as it passes through the condenser, in MW, (e) the mass flow rate of the condenser cooling water, in kg/ h, if cooling water enters the condenser at 15 DEGREE CELCIUS and exits at 35 DEGREE CELCIUS.
1. In a steam power cycle, steam enters the turbine at 30bar with the following different conditions and leaves at 1bar. Calculate Carnot efficiency, Rankine efficiency, condenser heat flow in kW assuming mass flow rate of steam as 9.5kg/s and steam rate for each case considering the pump work. (ii)Wet with 0.95 dryness (iii) Superheat at 550°C
Complete and legible solution please; The condensing pressure for a Rankine engine is 1 bar. Calculate the work net in KW and thermal efficiency of the cycle when the steam at the beginning of expansion is at 50 bar and (a) saturated, (b) 350 OC, and (c) 640 OC. Note: 1 bar is equal to 100 Kpa
A reheat steam cycle has 13500 kPa throttle pressure at the turbine inlet and 2800 kPa reheat pressure. The throttle and reheat temperature of the steam is 540°C. The condenser pressure is 3.4 kPa. Find the cycle thermal efficiency in %. Note: At 13.5 MPa, tsat = 333.88 deg C, sf = 3.5921 kJ/kg-K, sg = 55.4022 kJ/kg-K. FINAL ANSWER MUST BE IN 3 DECIMAL POINTS.
rankine cycle, the pressure and temperature entering the turbine is 1800 kpa and 380 degrees celsius and the pressure leaving the turbine is 20 kpa, the quality of steam entering the condenser is 90%. what is the turbine work in kj/kg at 1.8 mpa and 380 degrees celsius. engine turbine eff=85% mechanical ff=88% determine worknet,work brake, brake heat rate
Find the cycle efficiency and specific steam consumption of a reheat cycle operating between pressures of 3 MPa and 0.004 MPa, with superheat temp of 450oC Assume that the first expansion is carried out to the point where the steam is dry saturated and then the steam is reheated to the original superheat temp. The feed pump term may be neglected.
A power plant using a Rankine power generation cycle and steam operates at a temperature of 81.25°C in the condenser, a pressure of 5 MPa in the boiler and a maximum boiler temp of 775°C. The cycle operates at steady state with a mass flow rate of 2.5kg/s. Use the steam tables in the appendix of Sandler (p. 917 to 925). a.) Draw out the cycle, calculate the work required for the pump, the work output by the turbine, the heat into the boiler, and the heat out of the condenser. b.) What is the efficiency of this power plant? c.) If the turbine was only 89% efficient but still adiabatic (only generates 89% of the calculated work from part b), what is the overall efficiency of the cycle?
Please ASAP A Steam power station uses the following cycle - Steam at boiler outlet 150bar; Reheat at 40bar; Condenser at 0.1bar; working fluid expands and compresses at 700°C. Using steam tables and assuming that all the process are ideal. Determine 1.cycle efficiency of Rankine cycle with reheat 2.cycle efficiency of ideal Rankine cycle considering the turbine work is 990 kJ/kg
A rankine turbo generator unit receives 27000kg/h of steam at 1.2mpa and superheat by 122 degree. Condensate leaves at 22°c. For a brake steam rate of 4.74 kg/kwh, mechanical efficiency of 94%, determine (a) the ideal cycle thermal efficiency, (b) the indicated engine efficiency, (c) the condition of turbine actual exhaust, and (d) the turbo generator output in kw.
1. A reheat cycle with two stages of reheating is executed with steamexpanding initially from 90 bar and 530°C. The two reheaterpressures are 10 bar and 0.6 bar, and the steam leaves eachreheater at 480°C.Condensation occurs at 0.03 bar. Find the cycleefficiency.2. An ideal reheat turbine with one stage of reheat receives steam at8.0 MPa and 480°C. Reheat pressure is 0.83 MPa and exhaustpressure is 0.007MPa. The work is 1559 KJ/kg and thermalefficiency is 41%. Find the temperature of the steam leaving thereheater.